Independent third-party desk · Indonesia
Quality control inspection Indonesia — USD 135 / man-day, published.
Not SGS. Not QIMA. An Indonesia-based independent inspection desk with a rate card you can read before you book — plus the actual AQL accept/reject math on the page. The honest answer to "the QC failure we only found after the goods arrived."
- USD 135per man-day · indicative, as of 2026
- 100+photo-proof report, within 48h
- 24hquote turnaround, business hours
The instrument
Man-Day & AQL Verdict Bench
Two panels, zero contact-for-quote. Panel A estimates your man-days and cost at the flat USD 135 rate. Panel B turns a lot size into an accept/reject verdict. Every figure is your input or a value from the published tables — nothing is invented.
Rate & sampling data as of 2026, indicative. Final quote confirms scope. Paste it into the quote form below.
The anti "contact-for-quote" block
Published man-day rate card
One flat rate — USD 135 per man-day (about IDR 2,190,000), indicative as of 2026 — across every service. Typical man-days shown for a single standard lot at one factory; multi-SKU, multi-site and larger lots add man-days per the bench above.
| Service | Rate | Typical man-days | What one man-day covers |
|---|---|---|---|
| Pre-Shipment Inspection | USD 135 / day | 1 | AQL random draw, on-site defect check & 100+ photo report for one product at one factory. |
| During-Production (DUPRO) | USD 135 / day | 1 | Line-status check at part-output, early-defect flag and photo log before the run finishes. |
| Initial / Pre-Production Check | USD 135 / day | 1 | Raw-material and first-off verification before mass production starts. |
| Container Loading Supervision | USD 135 / day | 1 | Carton count, load condition, seal record and photos across one loading window. |
| Factory & Social Audit | USD 135 / day | 1–2 | Systems, capacity and social-compliance walk-through of one site. |
We are an independent inspection desk, not a certification body. Rate indicative as of 2026; the confirmed quote follows scope.
Checkable decision data
AQL sampling reference
ANSI/ASQ Z1.4 · ISO 2859-1, General Inspection Level II, single sampling. Lot-size band → sample-size code → sample size → accept/reject at AQL 2.5 (major) and 4.0 (minor). Transcribed as of 2026; very small lots follow the first applicable plan.
| Lot size | Code | Sample | 2.5 Acc/Rej | 4.0 Acc/Rej |
|---|---|---|---|---|
| 2–8 | A | 2 | 0 / 1 | 0 / 1 |
| 9–15 | B | 3 | 0 / 1 | 0 / 1 |
| 16–25 | C | 5 | 0 / 1 | 0 / 1 |
| 26–50 | D | 8 | 0 / 1 | 1 / 2 |
| 51–90 | E | 13 | 1 / 2 | 1 / 2 |
| 91–150 | F | 20 | 1 / 2 | 2 / 3 |
| 151–280 | G | 32 | 2 / 3 | 3 / 4 |
| 281–500 | H | 50 | 3 / 4 | 5 / 6 |
| 501–1,200 | J | 80 | 5 / 6 | 7 / 8 |
| 1,201–3,200 | K | 125 | 7 / 8 | 10 / 11 |
| 3,201–10,000 | L | 200 | 10 / 11 | 14 / 15 |
| 10,001–35,000 | M | 315 | 14 / 15 | 21 / 22 |
| 35,001–150,000 | N | 500 | 21 / 22 | 21 / 22 |
Lots above 150,000 pcs use codes P/Q — confirm the exact plan on booking. Values indicative as of 2026; verify against your current Z1.4 / ISO 2859-1 revision.
What actually gets checked
Category checkpoint matrix
The real on-site checkpoints per category. Every product line has its own inspection scope — here is what an inspector runs for the three we cover most.
Furniture
- Moisture % on solid-wood parts
- Joinery, glue-line & assembly
- Load & stability test
- Finish, colour & surface defects
Homeware & Ceramics
- Chip, crackle & glaze faults
- Dimensional & weight tolerance
- Packaging & drop test
- Set count & assortment check
Garment & Textile
- Measurement vs spec tolerance
- Stitching density (SPI)
- Colour / shade consistency
- Care-label & trim accuracy
Four steps · one honest verdict
How independent inspection works
- 01
Book
Send lot size, category and factory location. Quote back within 24 business hours — no "contact us" runaround.
- 02
On-site within 48h
An inspector reaches the factory and pulls the AQL sample per Z1.4 / ISO 2859-1 Level II.
- 03
Photo-proof report ≤24h
A report of 100+ images and the defect count lands within 24 hours of the inspection.
- 04
Accept / Rework
You get the independent pass-or-rework verdict — the answer that stops "QC failure found only after arrival."
Service commitments, as of 2026.
Where to next
Find your inspection route
Straight answers
Frequently asked
Are you affiliated with SGS or QIMA?
No. We are an independent Indonesia-based third-party inspection desk, not a certification body and not affiliated with SGS, QIMA or AsiaInspection. We name them only to be clear about what we are not.
What is a man-day?
One inspector working one day. Our rate is a flat USD 135 per man-day (about IDR 2,190,000), indicative as of 2026. Extra SKUs, factory sites and larger lots add man-days — the bench above shows how.
How is sample size decided?
By AQL under ANSI/ASQ Z1.4 / ISO 2859-1, General Inspection Level II. Your lot size sets the sample-size code letter, the number of pieces to pull, and the accept/reject thresholds — all in the reference table above.
Do you inspect my category?
Our core categories are furniture, homeware & ceramics, and garment & textile, with per-category checkpoints listed above. Send your product on the quote form and we will confirm scope.
How fast is the report?
An inspector is on-site within 48 hours of booking, and the 100+ photo report lands within 24 hours of the inspection.
No "contact for quote"
Get a fixed quote
Paste your bench summary, or tell us the lot size, category and factory location. A scoped quote comes back within 24 business hours at the published USD 135 / man-day rate. Prefer a form-free route? Use the contact page.
- Independent desk — no certification-body markup
- 100+ photo report within 48h
- Honest accept / rework verdict